How to cut wallpaper correctly?
To cut wallpaper correctly, you will need a straight edge and a utility knife. It would help if you also had an extra piece of paper to place under the wallpaper so that it does not get caught in the blade.
Start by laying your straight edge along the top of one corner of the wallpaper, ensuring that the corner is aligned with the joint where two pieces of wallpaper meet. Use your utility knife to make a small slit down from this point towards the floor. Now repeat this process for all four corners until all of the wallpaper is cut away.
Notch out each hole your utility knife makes with a thin piece of paper so that the wallpaper does not tear when pulled away. Once the holes are notch-out, pull the paper off, and you will now have perfectly cut wallpaper!
Measuring the wall
When measuring your wall, it is essential to take into account the length of each panel as well as the width. If you are cutting wallpaper that spans vertically and horizontally, divide the total measurement by two to find out how many panels you will need. For example, if your wall is 2 feet wide and 6 feet long, you need four panels. Utility knife
A utility knife is an essential tool for any homeowner. It can be used to cut through just about anything, making it perfect for cutting wallpaper. Tip: To ensure a precise cut, use a ruler to help guide the blade. Tip: If you do not have a utility knife, you can use scissors to cut the wallpaper. Be sure to hold the paper tightly against the wall, so it does not tear. Wallpaper cutter
If you decide to go with scissors, get a proper Wallpaper Cutter. These machines are designed to cut through wallpaper and simplify the process.
- Measure each panel's length and mark where you need to cut.
- Use your utility knife to slit down from the top corner of one panel towards the floor, ensuring that the corner is aligned with where the two panels meet.
- Repeat this process for all four corners until all of the wallpaper is cut away.
- Notch out each hole made by your utility knife with a thin piece of paper so that it does not tear when pulled away later on in step 5 below!
- Pull off the notch-out paper
Determine the start of the pattern
After cutting the wallpaper, you'll need to start laying it down in a pattern. To do this, line up the first panel with one of the starting marks and snap it into place using your fingers. Continue doing this until all panels have been snapped into place.
- Trace around each panel with a pencil or pen to mark where seams should be placed
- Cut along these lines with scissors
- Push each piece of cut wallpaper onto its respective seam so that they are flush against each other
- Check that all panels are in the correct positions and reinforce any areas that may need it using a hot glue gun or adhesives of your choice
- Finish up by trimming any excess wallpaper around the edges. You're now ready to start painting! If you choose to go with a Wallpaper Cutter, make sure to get one that is specifically designed for the task. These machines are much easier to use and will result in less damage to the wallpaper.
Cutting the strips of wallpaper on the trestle table
The trestle table is up, and the wallpaper roll prepares with a pencil, a cutting/craft blade, or a set of giant scissors. We advise wearing cotton gloves for wallpapers with very fragile or high-grade surfaces throughout reduction.
Currently, we can begin reducing the initial strip (or size). Put the wallpaper on the table, with the pattern encountering you, and roll it out. The formerly figured-out dimensions can be marked on the table ahead of time - or determine the roll and mark the paper itself.
Bear in mind to add 5 centimeters at the top as well as bottom of the strip. as well as inspect the pattern beginning. If it does not match the start of the roll, the cutting line must be adjusted (once again, plus 5 centimeters) first.
The cuts should always be at an appropriate angle to the roll. Either use a wallpaper leader or fold the wallpaper at the significant factor "side on edge," It also sufficed with your wallpapering knife or scissors.
The reducing process for the first size is identical for plain-colored wallpapers. Nevertheless, you can spread the wallpaper with the back encountering you as you do not need to fret about a pattern.
Keep in mind
You may think that rolls of wallpaper are produced in such a way that makes sure the top of the pattern will certainly be at the top (or end) of the wallpaper. Sadly, that is not the case - they are typically rolled up in a relatively arbitrary fashion (and direction). Please ensure you examine the instructions of the pattern to figure out the top and bottom appropriately.
Remember the pattern repeat for any additional strips of wallpaper.
Next, the added sizes are cut. Unlike plain-colored wallpapers without patterns, which can be cut off the roll one after the other, you must consider the pattern repeat dimension and counter when dealing with patterned wallpapers. This is necessary as it makes sure that you can make sure the pattern fits size by size. As mentioned in the past, the pattern repeat size is the height of the pattern duplicated on the roll (for example, "70 centimeters" implies that the pattern is repeated on the roll after every 70 cm).
Arrows encountering each other = Straight Match
No pattern repeat balance out required. The pattern will go to the very same elevation for all sizes of a wallpaper. Cutting extra lengths: the pattern is put on the pattern to see if the patterns are parallel at the sides/edges. If the trestle table is not vast enough to do this, the sizes need to be put side by side on the floor to figure out the start of the pattern. With this approach, there needs to be a minimal amount of offcuts.
Arrow as well as Number 0 = Free Suit
The pattern will be moved by regarding half a pattern repeat for the next size of wallpaper. For example: if the pattern repeat is 50 centimeters, the offset will undoubtedly be 25 centimeters. This suggests that every other size equals, i.e., size 1, 3, 5, etc. Yet size numbers 2, as well as 4, have 1/2 pattern repeat balanced out. When cutting, this indicates: You can reduce sizes 3 and 5 according to the initial length (by placing the pattern on the pattern). For sizes 2 and 4, you can check the offset by positioning length one as well as 2/ size three and four beside each other on the table or flooring. To decrease waste via offcuts (relatively high for this technique), you must utilize a brand-new roll for size number 2.
If you start wallpapering from the middle of the wall surface, please pay attention to the pattern suit to establish how you need to continue functioning to the left or right. This is important to make sure that the pattern matches on either side.
Note
Paper wallpapers have to be reduced on the trestle table. Non-woven wallpapers can be cut directly on the wall during wallpapering; must you favor this option approach? Nevertheless, in our choice, cutting the wallpaper on the trestle table is constantly simpler and much safer.
Also Read:- How to hang paper-based wallpaper?
For interesting Home decor Posts, follow us on Instagram.
Leave a comment